1. A tin-zinc alloy welded aluminum tank was used to heat and melt 60% tin, 35% zinc, and 5% aluminum in iron scoops and cast thin strips. Clean the oil in the cracks, grind the oxide film with an emery cloth, scrape clean with a screwdriver or a broken saw blade, and heat the aluminum parts to 300°C-40°C with a blowtorch (note that the temperature cannot be too high). Rub the electrode at the crack. When the electrode is melted, use a screwdriver to rub the molten electrode alloy at the crack to make the alloy flow into the crack, and then gradually thicken the layer.
2. Repair the tank with adhesive 1 Clean the cracks with a metal cleaner, scrape the paint, dirt, and rust there with a spatula, scrape the grooves along the cracks, and clean it again with gasoline. 2 Extrude the components A and B of XH-II adhesive in the same amount and mix it with the agricultural machinery I adhesive (about the above-mentioned adhesive to help I/3). 7 Cut two pieces of fiberglass cloth that is free of oil, is slightly larger than the grooved surface, and is coated with a layer of adhesive. 4 Place the adhesive-coated fiber cloth on both sides of the cracks for 10 minutes to 15 minutes, apply a layer of adhesive, and cure at room temperature for 25 hours.
3. Repair tank cracks with adhesive penetration method 1 Dry the water tank and drill 3 mm holes at both ends of the crack. If the cracks are long or curved, drill a hole in the center or corners and scrape the cracks with the breakage strip. , showing metallic luster. 2 Using 5O2 adhesive in two holes, riveted with 3mm aluminum rivets to seal the cracks. 7 Put the adhesive on the crack, then tap it with a hammer to make cracks in the cracks. Make the adhesive penetrate into the crack. Add 3 minutes of adhesive and tap. Repeat 2 times -4 times until the glue can't penetrate for 3 hours. - 5 hours to use.
2. Repair the tank with adhesive 1 Clean the cracks with a metal cleaner, scrape the paint, dirt, and rust there with a spatula, scrape the grooves along the cracks, and clean it again with gasoline. 2 Extrude the components A and B of XH-II adhesive in the same amount and mix it with the agricultural machinery I adhesive (about the above-mentioned adhesive to help I/3). 7 Cut two pieces of fiberglass cloth that is free of oil, is slightly larger than the grooved surface, and is coated with a layer of adhesive. 4 Place the adhesive-coated fiber cloth on both sides of the cracks for 10 minutes to 15 minutes, apply a layer of adhesive, and cure at room temperature for 25 hours.
3. Repair tank cracks with adhesive penetration method 1 Dry the water tank and drill 3 mm holes at both ends of the crack. If the cracks are long or curved, drill a hole in the center or corners and scrape the cracks with the breakage strip. , showing metallic luster. 2 Using 5O2 adhesive in two holes, riveted with 3mm aluminum rivets to seal the cracks. 7 Put the adhesive on the crack, then tap it with a hammer to make cracks in the cracks. Make the adhesive penetrate into the crack. Add 3 minutes of adhesive and tap. Repeat 2 times -4 times until the glue can't penetrate for 3 hours. - 5 hours to use.
Function:strongely effective on chlamydia, mycoplasma, enterbacteriaceae infection, and mixed infection. protect eyes, clean respiratory tract, and protect mucosa, strengthen the first proective screen of immunity.
Indications: Monocular cold, weeping tear, swollen eyes, swollen face, secretion like water or pus. Diarrhea, kelly stickiness stool ,bradypsychia, Nasal tumor swollen, Oral cavity mucous membrane turns purple, patient appears yellow green slime ,left nose, dyspnea, air sacculitis.
Doxycycline Hyclate Powder,Doxycycline Tylosin Powder,Doxycycline Tablet For Cattle,Doxycycline Spiramycin Tablet
Hebei Kexing Pharmaceutical Co., Ltd. , http://www.kexingpharma.com