With the popularity of solar insecticidal lamps , many places have begun to use solar insecticidal lamps to kill insects, but many people do not know how to install insecticidal lamps. In order to make everyone better use, we will provide you with The detailed steps of installing and using the solar insect killer light, I hope to help everyone!
The first step: foundation pouring
1. Determine the location of the vertical lamp to investigate the geological conditions. If the soil is soft and soily, then the bottom of the foundation should be compacted. At the same time, it is confirmed that there is no other facilities in the underground. There is no long-term sunshade on the top of the insecticidal lamp (including the forest cover). position.
2. Digging the pit, excavating the standard soil pit according to the size of the embedded part in the position of the standing lamp, and positioning and pouring the embedded part according to the construction drawing. Pay attention to keep the foundation on the same level as the original ground, and at the same time, the top of the screw of the embedded part shows that the cement base does not exceed the thickness of the two fixing nuts.
3. After the cleaning is completed, the residual sludge on the positioning plate (cement plane) should be removed immediately, and the impurities on the bolts should be cleaned with waste oil.
4. The solidification process of cement solidified cement is generally 72 hours, and the winter is properly extended. After the solidification of the susceptor is completed, the solar lamp can be installed.
Step 2: Solar module installation
1. The output of the panel assembly should be taken as far as possible to avoid shorting before connecting to the solar controller.
2. The connection between the solar cell module and the fixed bracket should be firm and reliable.
3, the output line of the component should be avoided as much as possible, and tied with a tie.
4. In most parts of China, the angle between the panel of the panel and the ground is generally chosen to be 30°, and the panel is slightly westward toward the south.
The third step: battery installation
1. When the battery is placed in the battery slot, it should be handled gently. If the battery slot is not suitable, it should be treated to ensure that the battery is easy in the slot.
2. The battery output line is not allowed to be shorted under any circumstances.
3, the battery should be 5cm below the battery slot, it is strictly prohibited to be higher than the battery slot.
The fourth step: installation of lamps
1. Fix the solar panels of each component on the solar bracket, fix the head of the street lamp on the pick arm, and then fix the angle and direction of the solar panel bracket to the main pole of the lamp, and follow the instructions of the on-site construction technician to kill the solar energy. The lamp sling is hung on the cross arm and fixed in the lower part of the insecticidal lamp, and the connecting wires are led to the solar insecticidal lamp control box. Note that each lead is not short-circuited during lead threading.
2. The installation of the solar controller is fixed on the main pole according to the construction diagram.
3, the use and adjustment of the solar controller (1) charging indicator green is always charging for charging, green flashing for the system over voltage, check whether the battery is connected (2) battery status indicator is steady green: battery voltage is normal Range, after full, it is green and slow flashing, orange: battery undervoltage red: over-discharge voltage, controller automatically turns off output (3) The load indicator is always on, indicating that the load is turned on, flashing indicates that the output has a short circuit, and slow flashing indicates the load Overload, should reduce the load (4) Timing setting method Time setting on the back of the solar controller, time setting, corresponding time of the toggle switch
1 [10H] 2 [8H] 3 [5H] 4 [4H]
4. Adjust the solar controller to check if the solar insecticidal lamp is normal. (1) Observe whether the indicators are correct. (2) Is the debugging system working properly?
Step 5: Debugging
1. Light control function debugging Release one of the solar panel connection lines on the solar controller. Each light source should work normally. There is voltage on the high voltage net of the insecticidal lamp; connect the solar panel connection line on the solar controller, and each The light source is extinguished and the insecticidal lamp mesh has no high voltage.
2. Rain control function Debugs one of the solar panel connection lines. After the system is running normally, test the rain control components with a damp cloth or dripping water. The system should stop working. After removing the wet cloth or wiping the water droplets, the system should work normally. Indicates that the system has normal rain control.
3. The time control function debugging can be set and tested according to the timing requirements.
Installation Precautions
The red line is positive and the other lines are negative.
1. The positive and negative terminals of the terminal can not be shorted, that is, the positive and negative poles cannot be connected.
2. The positive and negative terminals of the terminal block cannot be reversed.
3, the terminal can not be grounded
The above is the installation procedure of the solar insecticidal lamp. When using the insecticidal lamp, the above steps must be strictly installed to avoid unnecessary trouble and affect the use effect and life of the insecticidal lamp.
Goggle,Breathable Safety Goggle,,Protective Disposable Goggle
Dongguan Keyutai Mask Co., Ltd. , https://www.maskkytai.com